The peat, the dykes and the medieval reclamation
The medieval reclamation of the Alblasserwaard made it possible to live on and cultivate a plain in which water tended to stagnate. To drain the land, ditches and collecting canals were dug and dykes were built. A surface thus delimited, with an artificially regulated water regime, takes the name of polder. The drainage had a long-term effect. The peat, relieved of saturation, compacted and the surface of the land sank. In time the difference in level that allowed water to flow away diminished, while the level of the rivers could exceed that of the cultivated areas.
The digging of canals and the maintenance of sluices required agreements between settlements that shared the same outlet. The water boards of Overwaard and Nederwaard developed networks still recognisable today. According to UNESCO documentation, their lower basins date from 1365 and 1369 respectively. Part of the landscape therefore predates by several centuries the mills that dominate the view. The seats of the water boards preserved within the perimeter belong to the same history. Their interest lies in the relationship with the installations, since those in charge had to coordinate resources, works and discharges affecting several communities.
The path of the water from the fields to the river
Rain collected by the ditches of the fields reached the drainage canals. The water could be raised towards a common collecting basin, called boezem in Dutch. Here the mills of the two batteries transferred water from the lower basins to the upper ones, separated by dykes. The greater height of the stored water made it possible to empty the upper basins by gravity through the sluices of Elshout when the level of the Lek allowed it. During flood phases a part of the water was held in the basins while waiting for a more favourable condition for discharge.
This route helps in understanding the placement of the sails along the dykes and the usefulness of the relatively wide waters seen between the groups of mills. The wind turns the sails, the shaft transmits the motion to internal gears and, in the mills with a wheel, the paddles lift the water through a passage built into the dyke. Following the bank beside the Blokweer mill open to visitors, the external position of the wheel can be seen, a valuable element for imagining the transfer concretely. The mill works on a limited difference in level, while the network links several passages and offers room to accumulate water temporarily.
Two eighteenth-century rows and the Blokweer mill
The eight mills of Nederwaard, built in 1738, have circular brick towers. Those of Overwaard, also eight, date from 1740 and are distinguished by the octagonal body and the reed cladding. From the route along the canals the material is the first clue for recognising the two groups. Then one can observe the silhouette of the tower, with the faces of the octagon becoming visible when the sun lights two sides differently. Including the two mills of Nieuw-Lekkerland and that of Blokweer, UNESCO distinguishes in all eight masonry towers, ten octagonal mills and one hollow-post mill.
At Blokweer the whole upper part can be turned to point the sails into the wind. The structure at the base and the movable body can be told apart at a glance, especially from a slightly lateral position. The present mill dates from 1630, and a map of 1542 attests that the place was already occupied by a similar machine. The installation served the Blokweer polder together with an auxiliary station until an electric pump took over in 1957. After the serious fire of 1997, the restoration recovered the surviving historic elements. The silhouette that is seen therefore bears traces of several episodes, from local water management to the conservation of the machine.
Two mills of the Nieuw-Lekkerland polder complete the whole, their names signalling the role taken on at different heights. The Hoge Molen dates from 1740, the same year as the Overwaard row. The Lage Molen was rebuilt in 1761 after damage to the earlier structure. The two machines help to distinguish the scale of the individual polders from that of the basins that received water from several areas. Local history also recalls the Oude Molen, which suffered the breaking of its shaft in 1945 and was dismantled in 1957. Some of its parts were reused in other mills. To find one’s bearings among these names it is useful to start from the map of the site and to observe how the machines are distributed along the canals, even beyond the rows that first catch the eye.
In the millers’ rooms
In the museum mill of Nederwaard the visit leads inside a brick tower equipped for work and domestic life. The body of the machine has an imposing volume when seen from the bank. Inside one understands how little space remains between the curved wall, transmission parts, stairs and the family’s rooms. The gears are close to the visitor route. It is worth observing how steep the stairs are and how the lived-in spaces adapt to the structure. A good part of the available space was conditioned by the need to pass the motion from the sails to the pumping device.
At Blokweer the visit extends to the courtyard and reconstructs scenes of life in the 1950s. The small vegetable garden and the traces of work in the open help to grasp how the family obtained part of what it needed beside the place of work. Closeness to the machine mattered even when the weather and the wind changed. Turning the sails, adapting the surface of the canvas and checking the operation required practice. The inscription, in 2017, of the craft of the Dutch miller on the UNESCO Representative List of the Intangible Cultural Heritage concerns this transmission of skills, supported today also by training and apprenticeship.
Wisboom and motor pumping
In 1868 the steam-powered Wisboom station entered service. It made it possible to lift water during calm spells, when the mills could not work. In 1924 the station passed to electricity. The visit to the engine room introduces another scale of power and different ways of regulating the installation. The comparison with the wheels driven by the sails works particularly well after observing a mill closely. Both systems had to overcome differences in level within the same network, with different sources of energy and possibilities for intervention.
The choice to place the new installations along the existing basins made it possible to continue water management while preserving the historic layout. The mill and the engine stood side by side during a long transition. Today ordinary drainage relies on modern stations, and the UNESCO dossier describes the historic mills as machines kept able to operate as a reserve. At De Fabriek, an auxiliary station with exhibition spaces, the introductory film gives an overview of the system. Those who begin here can recognise in the open the passages illustrated and find again at the end the outlet, where the waters from the plain reach the river.
How to spend the time on site
With two or three hours available it is advisable to start from the reception area and devote time to the explanation of the system before reaching Nederwaard. The operator’s proposal passes through De Fabriek and Wisboom and reaches the museum mill with the Hopper boat. A walk along the bank makes it possible to observe the opposite row at one’s own pace and to return on foot after the visit. Those with an hour can choose a walk with a single stopping point or favour the historic station if the weather is unfavourable. Entry to the exhibition sites requires a ticket. It is advisable to check the conditions on the operator’s website together with the boat departures.
With half a day Blokweer can be added, time given to the courtyard and the walk alternated with the low viewpoint from the water. On the boat the sails stand out more sharply against the sky and the passages between banks and canal are seen from close up. On foot the alignments are better grasped and one can turn back to compare two machines. For those visiting with children, a detail can be assigned to each stop, for example looking for the octagonal profile after seeing a round tower. The wheel at Blokweer then offers a point at which to reconstruct together, pointing to the bank, the direction in which the water was lifted.
Accessibility and conditions along the canals
The plain is open to the wind and there are exposed stretches along the canals. A light waterproof jacket and shoes suited to walkways and steps are practical even when sun and cloud alternate. At narrow points it is better to stop leaving a passage clear, especially when taking photographs near the entrances to the mills. In the busiest hours the walkways can slow the visit. The time saved by a crossing by boat must be weighed against the actual frequency of departures and the time needed to board.
For those using a wheelchair or having difficulty on stairs, the operator publishes measurements of thresholds, ramps and passages. At Wisboom the entrance bridge has a slope and the passage towards the engine room is narrower than the entrance door. To reach the interiors of Nederwaard and Blokweer there are steps, and at Nederwaard the interior staircase leaves little room. The rear deck of the Hopper has places for wheelchairs. To organise a visit with specific needs, it is advisable to check access to the boarding point and availability, and then to choose the stops according to the possibility of seeing machines, basins and differences in level from outside.
Reading and photographing how the site works
A photograph that includes in the foreground the edge of the canal and the dyke preserves more information about the landscape than a frame of the tower alone. On the bank of a canal one can compose an image in which the opposite group repeats at regular intervals, then move closer to a machine to show the form of the body and the materials. With side light the difference between brick and reed covering stands out. When the water is rippled, one can look for details of the bank and of the hydraulic passages, which remain legible even without reflections. The profile of Blokweer deserves a separate pause, precisely for the form of the upper body.
The wet meadows and the banks are also part of the environment shaped by the regulation of water. Between one stop and the next one can observe where the margin is grassy or covered with reed beds and where the drainage work needs an equipped bank. On these stretches the paths open to the public make it possible to see the installations while keeping a distance from inhabited houses, fences and moving machines. Ripples and wind change the look of the canals even in the course of a morning. A second look from the same small bridge can reveal the opposite bank when the sails and the light take on another inclination.
The meaning of the UNESCO inscription
The inscription is based on criteria (i), (ii) and (iv). The first recognises the ingenuity with which the territory was defended and drained over centuries, the second the circulation of Dutch reclamation techniques and the third the conservation of an ensemble in which architecture, landscape and hydraulic function remain legible. The continuity is evident on the route that joins installations of different epochs. Each generation had to adapt the way of moving water, while the places of collection and discharge have kept recognisable relationships. The conservation of the dykes and of the views is also part of the protection of these relationships.
Before leaving Kinderdijk, the area near the outlet on the Lek is a good place to put the route back together. From the canal side one sees the places where water could be held back, while towards the river the destination of the discharge is recognised. The complex is better read by walking it in both directions, with a first pass for orientation and a second for observing the details. The dyke that seemed a path between towers and meadows thus takes on the function it had for the inhabitants of the plain, that of keeping fields, water reserves and river course in relation.