The rock, the water and the depth of the shafts
In the copper and tin mines, tunnels were needed to reach the lodes and shafts to bring men, tools and extracted material to the surface. The workings descended deep and could extend a great distance from the visible entrance. When the tunnels intercepted water, the ability to keep them usable decided how far work could continue. Draining and extracting were therefore two linked problems. Keeping access to the lode was worth little if the lower parts of the workings could not be kept dry. Above ground, the position of the pumping engines still makes this relationship legible.
The public space around the ruins gives back only part of the installation. From a roofless engine house one can sense the height needed for the engine and the beam. The spoil heaps indicate the quantity of rock that was removed to obtain the useful material. Slopes and platforms can signal points of passage between different phases of processing. First identify the shaft or its enclosure and look for the nearest engine. The layout helps in understanding how the load moved, at what level the transfer took place and where a different operation began.
On the coast at St Just some workings also extended beneath the sea. The line of the cliff that appears clear in photographs was therefore a limit of the visible landscape, while underground what counted were the direction and continuity of the lodes. Botallack is instructive precisely because the margin between land and sea is seen at once. A section drawing or a reading of the panels can link that view to the underground work, which for the most part remained outside the visit. Along the coast the ruins and shafts can be read from the open paths indicated by the operator.
Steam engines and the forms of the engine houses
The beam engine transformed the movement produced by steam into a movement transmitted outside the building. In pumping installations the connection reached the rods in the shaft. There were also engines intended for hoisting loads or crushing the material. The masonry had a mechanical function. The wall that supported the beam had to withstand the stresses of the effort at a precise point. Looking at the form of the building and the edge of the shaft, one can reconstruct from which side the movement emerged and how much space was reserved for the internal components.
Steam technologies were modified several times in response to local needs. At the beginning of the 18th century Thomas Newcomen’s atmospheric engine made pumping on a larger scale possible. Over time other designers worked on the use of steam and on fuel consumption. In Cornwall Richard Trevithick experimented with solutions to increase the efficiency of the energy used, including the application of high-pressure steam. Reducing the amount of fuel needed to lift water meant making more demanding workings economically viable. The innovations directly changed the depth and extent of operations.
The chimneys remain among the easiest parts to recognise from afar. On approaching, the thickness of the engine house, the high openings and the relationship with the adjacent structures become important. If several buildings remain on the same site, ask which were connected to a shaft and which to a processing plant. Two similar buildings could power different operations. The visit to a preserved engine clarifies the movement and makes it possible to return to observe the masonry with a scheme in mind, which also helps at sites where only the walls are visible.
From Botallack to Levant along the Tin Coast
In the St Just district the coast gathers within a short distance places linked to different times of production. At Botallack, the engine houses of the Crown Mines are read in their position relative to the water and the approach routes. From an authorised point on the path, observe the succession of structures on the slope. The different orientation of the walls helps in imagining the relationship between engines, shafts and service space. On the exposed stretches the condition of the path and the weather matter. Consult the map and the notices of the National Trust before linking several sites on foot.
At Levant the working of a historic engine can be explored in more depth. The National Trust presents the beam engine installed in 1840, restored in its original position. The movement makes evident the connection between a source of energy and the work of moving material. The site also preserves another story, that of the man engine accident of 1919, a device used to carry workers between levels of the mine. Thirty-one people lost their lives there. The distinction between the machines used for the ore, for the water and for transporting workers helps to grasp the complexity and risk of the work.
Those with half a day can choose between the exterior of Botallack and a scheduled visit to Levant. If several places on the Tin Coast are to be combined, set aside time for the transfer and for reading the ruins from different points. Straight-line distances make structures separated by differences in level, property or gates appear close. A shorter visit, built around one installation and two observations from the public path, is enough to understand how the coast entered into the organisation of the mine.
Geevor and the transformation of the extracted material
Geevor makes it possible to follow the ore beyond its exit from the shaft. Here extraction ceased in 1990 and the mine’s plant gives a good picture of a late phase of the industry. In the spaces of the mill one can observe the passage from the extracted rock to a saleable tin concentrate. The machines intervened at different stages. First the size of the fragments was reduced, then the material was refined and the useful components separated. Lifting the rock was therefore only one of the operations. The processing plant crossed during the visit explains why production also required space, energy, water and staff at the surface.
When the route is available, the underground visit enters the tunnels of Wheal Mexico, an older mine included in the Geevor site. They are two testimonies to be placed side by side. The tunnels open to visitors tell of the conditions of historic underground work, while the surface plant makes it possible to follow the chain at another stage. Before buying a ticket, check which parts of the complex are open and consult the guidance on the conditions of the route. Devote time to the mill even if the descent has been chosen. The path of the extracted material better clarifies the link between the tunnel and the buildings seen from afar.
From the foundries to the sea between Hayle and Charlestown
At Hayle it is worth shifting one’s gaze towards the harbour and the traces of the foundries. Supplying machines to the mines required workshops able to cast and work the components and to ship them to the sites. The harbour could ease the exchange of raw materials, fuels, machines and products. Its form gives back a phase different from the view of a cliff or a shaft. Look for the surfaces where it was possible to unload and store materials. Then consider the distance between the landing point and the work areas. The industrial territory often began from that link.
On the southern side of Cornwall the area of the Luxulyan Valley and Charlestown offers other examples of infrastructure. The valley presents works serving industry, including canals, tramways and the Treffry Viaduct, which also served as an aqueduct. A visit allows one to understand how water and loads were carried across a steep valley. At Charlestown the form of the harbour helps in recognising the stage of shipping, decisive for an economy that exported minerals and products. The two stops read the same chain from two angles, from the place where the material passed to the one from which it left the coast.
Camborne, Redruth and the copper of the moorland
Between Camborne and Redruth the official map of the mining routes relates towns, plants and coast. In the houses and public buildings of the two towns the society that lived off that industry takes shape. At East Pool the machines that served the shafts can be studied, while King Edward Mine tells of the technical training for work in the mine. On the Wheal Peevor side, the preserved structures help in following on foot spaces that on paper appear much closer than they turn out to be on the ground. The vein of the Great Flat Lode adds a geological element to the visit. Rich in tin, it stands out for its relatively gentle inclination, a feature that conditioned the distribution of extraction activities.
The link with the port of Portreath makes the material balance of the district legible. Towards the coast travelled copper ore, while coal coming from the sea took the opposite route. Landing places, junctions and storage spaces were needed. Read the map of the mines and that of the links together to understand why the UNESCO site also includes stretches far from the shaft entrances. Starting with a short route near Redruth makes it easier to recognise these links in the landscape.
On Bodmin Moor the Caradon district tells of another copper boom. Around Minions and Caradon Hill remain the traces of the mines and of the communities that grew up near the plants. The nearby town of Liskeard also preserves buildings that bear witness to the wealth produced by the district. The heritage map follows part of the railway corridor towards the town. On the moor, the uneven surfaces and sloping stretches require more time than the distance suggests. From the authorised path, where the distribution of the ruins remains clearly legible, the map of the plants can be compared with the profile of the settlements.
Tavistock, the Tamar and the mining communities
At the eastern end of the property, the Tamar Valley crosses the border between Cornwall and Devon. Here the mining landscape includes slopes, settlements and places of handling along the river. The minerals extracted and processed in different areas were transported towards the points of exchange. At Tavistock, the changes in the form of the town make it possible to trace back to production the capital invested in urban spaces. Observe the size and position of the service buildings in relation to the access roads. Those who arrive after seeing the Tin Coast recognise two industrial geographies, one articulated along the cliff and the other among valleys, uplands and river.
In the productive districts surface activities were also part of the work. The extracted material was sorted and prepared before the later processes. The so-called bal maidens, women workers often engaged in preparing the mining rock, are a part of the story that is well understood in the museums and in the materials of the site. The dwellings of the workers and the small plots near the villages also help to reconstruct the link between wages, domestic life and local resources. Looking at the inhabited places after the plants means reassembling a landscape that for many families was at once a workplace and a residence.
A story that goes beyond Cornwall
The local mining industry maintained relations with distant markets. When metal prices and international competition changed the conditions of production, many workers left. Communities of Cornish origin took part in the mining industry in other countries, including Mexico, Australia and South Africa. The movements carried with them work skills and technical knowledge. In some cases even the form of the plants and the memory of places were transplanted to very different territories. This helps to understand the presence of the UNESCO criterion concerning the circulation of knowledge and technologies.
Distribute the visits starting from a question. To understand the relationship between shaft and steam, choose Levant or another site with interpretable apparatus. To see how a concentrate was obtained, devote time to the mill at Geevor. To follow the exchanges, observe an industrial foundation and a port or a stop along the Tamar. The areas are large and organising the transfers makes it possible to keep time for the routes and for the points where it is worth stopping. Museums, visitable plants and public footpaths have separate access arrangements, to be checked even when they are in the same district.